Showing posts with label Infrastructure. Show all posts
Showing posts with label Infrastructure. Show all posts

Sunday, January 31, 2010

Entering the Digital Age!



In honor of the dip in temps in our neck of the woods, I thought that today would be all about gas.  Not methane, though we have quite a bit of that thanks to Hubs.  I am talking about natural gas, the kind we use to heat our house. 

We have a multi-zone, natural gas fueled, hot water baseboard heating system with four thermostats.  Zone One is the Family Room and Kitchen*, Zone Two is the Dining Room and Living Room*, Zone Three is the Office and Front Bedroom*, Zone Four is the Master Bedroom* and the Center Bedroom, Zone 5 is the bathrooms (this zone comes on whenever another zone kicks on). The * denotes which room the thermostat is located in.

It is quite nice because we are able to turn the heat up in only the areas where we are hanging out versus heating the entire house.  The not nice part?


We had the old fashioned "lever style" thermostats.  You know the kind I am taking about.  The ones where you have to guestimate and eyeball what the current temp is and hope the temp you want is the temp you are setting it for.  Personally I loath these types of thermostats.

After getting a wake up call in the form of our December natural gas bill (more than double November's), we realized that we needed to get a better handle on how we are heating the house.   Solution:  digital thermostats.  Like these.


We went with the most basic model since we didn't need it to be programmable and we only have a 2-wire system.  We got these at Home Depot for about $25.00 a unit.

Then it was a matter of switching them out.  The switching out part was easy.  Since we have a 2-wire system, we only had two connections to make.    Here is a tip:  Take a pencil and wrap the wire you removed from the old fixture around it.  This will ensure that the wire won't fall back into the wall. 

One hiccups we found was that some of the thermostats had an old-fashioned mercury switch.  Needless to say once those were carefully removed, they got double bagged and placed in the basement waiting to be brought to our county's Public Works Department for proper disposal since placing liquid mercury in the regular trash is a big no no.

I swear this gizmo looks like a high school science project from the 50s.

It actually took more time to sand, spackle and paint the area that was previously covered by the old thermostats.

  

  

 



No these were not taken all in the same room.  I realized that I hadn't taken photos of all the stages in any one room.  Whoops.  So you get to see the Benjamin Moore Riviera Azure from our front bedroom, the awful tan from our living room and Valspar Key Lime Pie from our kitchen.

Now all we need to do is wait to see if being able to set each zone to a definite temperature will result in lower bills or at least not the same shocking jump we saw in the last bill.  Personally, I think it will be the latter since January is our coldest month here is Michigan.   

Will keep you posted when we get out bill for the last week of December and the first three weeks of January.  

Tip of the Project:  After you disconnect the thermostat wires, wrap them around a pencil to ensure they don't fall back into the wall.

Friday, January 29, 2010

Making a Square a Circle



As you may remember, a few weeks ago I made the surprising discovery that several of the bedroom doors had less than optimal doorknob holes (like the one above).  It made replacing the original "attractive" 70s brass doorknobs with the new brushed nickel ones problematic, to say the least.

So we purchased one of these and got to work. 

The problem?  Since there was already a hole in the door, how would we use the hole saw bit to round it off to make an actual circle.

After some trial and error (OK, more along the lines of the saw jumping and skipping around the hole and me using an interesting selection of words not to be used in polite company), Hubs and I figured out how to make the process work smoothly. 

Here's are the steps we worked out.

1.Place the door across your saw horses.  You will be drilling through the door, so you don't want to put it on a solid surface.

2.  After placing the correct sized hole saw on your drill, start the bit spinning.

3.  Bracing yourself, place the edge of the bit at an angle at the edge of the circle you want to drill. Create a small groove.

 

4.  Slowly rotating the angle of the hole saw, repeat step 3 on another side of the circle.


5.  Repeat step 4 on the third side of the hole.


6.  At this point, using the grooves you created earlier as a guide, straighten the hole saw and applying pressure begin to work the saw through the door.  The grooves should keep the saw in line until you get further into the door.


7.  Eventually, you will make it through the door.



Now you have the correct sized hole for your doorknob.

I do have to be totally honest, I did have some skipping on my door (which caused some rather colorful language to be uttered during this endeavor.) . 



However, it wasn't anything that a little sandable wood filler and a coat of white semi-gloss paint didn't fix.

And this


looks so much better than this.


If the instructions weren't clear or you have any other tips, please let us know. 

I am sure we will run into more doors that need some "rounding off" as we continue to replace our doorknobs.